One moment your LG washing machine is operating fine, and the next minute you have a dreaded error code.
- Washing Machine Caddy Error Codes Free
- Washing Machine Caddy Error Codes For Sale
- Washing Machine Caddy Error Codes For Windows 7
- Washing Machine Caddy Error Codes Download
- Washing Machine Caddy Error Codes 2017
Is your washer displaying the LE error code?
There are several reasons this can occur.
While it is a pain, there are things you can do to troubleshoot and fix the problem.
Here’s a look at what may be going on.
What Is The LG Error Code LE?
E32 appears in the display: The washing machine flashes alternately with “end” at the end of the programme. This is not a fault. The unbalanced load detection system has interrupted the spin cycle because the laundry is unevenly distributed. Power-off memory function: In case of abrupt power failure or the need to cut off the power during a program cycle, the present settings will be saved and the preset operation will resume when the power is on again. Note: During the spin process, if too much foam is inspected, in order to protect the motor, the washing machine will eliminate the foam automatically; the motor will stop and the. Unbeatable deals, free delivery and price match on the best range of cookers, ovens, washing machines, fridge freezers and more. Find everything you need at appliancentre.com or visit us in our Finchley store.
The code LE means that the motor in your washer is locked.
Sometimes this may simply be due to a wash load that was too heavy.
However, in more severe cases it can indicate you have a failed rotor position sensor, a broken motor, or damaged sensor or motor wires.
First Steps To Take
To determine if the error code is being shown due to a heavy wash load you should first try to reset the machine.
Follow these steps to complete this process:
Press the POWER button to shut the washer off.
Unplug the washer from the wall or flip the circuit breaker.
While the power is disengaged, press and hold the START/PAUSE button for at least 5 seconds.
Flip the breaker back to the “on” position or plug the washer back into the wall.
Did this do the trick? If the code is not cleared you will have to continue troubleshooting the other issues.
How To Troubleshoot & Fix A Locked Rotor
If the LE code on your LG washing machine is accompanied by loud “clanking” noises you’ll need to check the rotor on the unit.
Here’s how you go about this:
1. First unplug the power cord from the wall and turn the inlet water supplies off and disconnect all hoses.
2. Pull the washer far enough forward that you can easily gain access to the back of the machine.
3. Next, you’ll need to remove the screws on the back of the washer that hold the back panel in place.
Flex the panel enough to release the tabs found at the top or bottom (location depends on your model).
4. Remove the bolt that attaches the rotor to the tub shaft. You may need to hold the rotor still while you torque the bolt.
5. Since there may be sharp edges involved, it’s highly recommended that you wear gloves when doing this process. Minitool partition wizard 2018.
6. Grasp the rotor firmly and pull it straight off the shaft.
Washing Machine Caddy Error Codes Free
Once you have the rotor off, you’ll want to check the teeth to see if any are missing or if they are stripped.
If so, you’ll simply buy the new part and replace it.
How To Troubleshoot & Repair A Failed Rotor Position Sensor
The rotor position sensor (RPS), or hall sensor, is an important part of your washer’s automated system.
It assists the control board with determining everything is working normally.
The hall sensor monitors the motor in your washer and makes sure it runs properly.
If this sensor fails it can cause the LE error code. Here’s how to replace it:
1. For this fix you will disconnect all power from the machine.
Washing Machine Caddy Error Codes For Sale
2. Pull it far enough forward so you can access the back panel.
3. Next, you’ll remove the screws on the back of the washer that hold the rear panel in place. Pull up on the panel to release it.
4. Remove the bolt that holds the rotor to the tub shaft.
You may need to hold the rotor while you loosen the bolt.
It also works well to have someone open the washer door and hold the tub inside so it doesn’t move.
Again, wearing gloves is a great idea as you may encounter some sharp edges.
5. Grasp the rotor and pull it off.
The rotor position sensor is located at the bottom of the stator.
6. You’ll need to unscrew a couple screws to allow you to unhook two connectors.
7. After the screws are removed you’ll need to remove all bolts holding the stator in place.
Just be sure to hold the stator as you remove the last bolt so it doesn’t fall off.
8. Once the stator is loose you’ll simply fold it down and you’ll clearly see the RPS.
9. Now remove the two wiring harnesses from the switches.
10. Remove the RPS from the stator and snap the new one in place. .
Washing Machine Caddy Error Codes For Windows 7
Reassemble your washer and the issue should be gone.
If this repair didn’t fix your issue you’ll need to check the motor and see if the sensor wires are damaged.
How to Troubleshoot & Repair Damaged Motor Or Sensor Wires
While you have the back off of your LG washing machine and you’re looking at the RPS and rotor, it’s a great idea to check for any damaged wires in this area.
The LE code can be caused by an issue such as this.
So, before you buy any replacement parts you may want to check the wires.
To do so you need to follow steps 1 through 6 to disassemble the washer.
1. Once you have the stator off and you can visibly see the wiring harnesses that connect to the motor and the rotor position sensor, check for wires that are burned or damaged in some way.
You’ll see wire colors red, yellow, and blue.
2. If you find any wires that have sustained damage it’s important to fix them.
To do so you can use heat shrink to reconnect the wires.
3. If they are too damaged to hold with this repair you will need to remove and replace the wires with new ones.
If you’ve tried all repairs we’ve suggested above and your LG washing machine is still displaying the LE error code you will more than likely need to contact LG’s support center or a local appliance repairman.
The issues we’ve discussed are the most common reasons the LE error code will display, however, from time to time there may be other issues.
Did your LG washer begin displaying this code?
Washing Machine Caddy Error Codes Download
Did you make any of our suggested repairs above and did it work for you?
Washing Machine Caddy Error Codes 2017
Comment below and let us know what you encountered, or any other tips you can offer.